Micron Technology 계산하기

MT29F4G08ABBEAH4:E

A: The MT29F4G08ABBEAH4:E is based on Single‑Level Cell (SLC) technology, offering high endurance and long‑term data retention. The table below summarises its core specifications, drawn directly from manufacturer data and multiple distributor sources: Specification Value Memory Density 4 Gbit (512 MB) Memory Organization 512M × 8 bits Memory Technology SLC NAND Flash (Single‑Level Cell) Memory Interface Parallel asynchronous Page Size 4320 bytes (4096 + 224 bytes spare) [13†L8-L9] Block Size 64 pages per block (256KB + 14KB spare) [12†L12-L13] Plane Organization 2 planes × 1024 blocks per plane [12†L13-L14] Total Blocks 2048 blocks [12†L14] Supply Voltage (VCC) 1.7V to 1.95V (1.8V nominal) [5†L13][8†L11] Asynchronous I/O Timing (tRC/tWC) 30 ns (at 1.8V) [12†L15] Page Read Time (tR) 25 µs (typical) Page Program Time (tPROG) 200 µs (typical) Block Erase Time (tBERS) 2 ms (typical) [12†L15-L16] Active Supply Current 20 mA (max) [6†L7] Operating Temperature (Commercial Grade) 0°C to +70°C [5†L14][8†L10] Package Type 63‑ball VFBGA (9 × 11 × 1.0 mm) [7†L12] RoHS Status ROHS3 Compliant, Pb‑free, Halogen‑free [5†L13][8†L13] Moisture Sensitivity Level (MSL) 3 (168 hours) [5†L16][8†L10] Additional features include: ONFI 1.0‑compliant command set with advanced commands: Program page cache mode, read page cache mode, one‑time programmable (OTP) mode, block lock, programmable drive strength, two‑plane commands, multi‑die (LUN) operations, read unique ID, and internal data move [12†L16-L19]. Hardware status monitoring via a dedicated Ready/Busy# (R/B#) output [12†L22]. Write protection of the entire device via the WP# pin [12†L23]. First block (block address 00h) valid when shipped from the factory [12†L23-L24]. RESET (FFh) command required as first command after power‑on [12†L25].

A: The device uses a standard parallel asynchronous NAND Flash interface. To keep the pin count low, the I/O pins are used as multiplexed address, command, and data ports. The interface consists of the following signals [7†L15-L20]: Signal Function I/O0–I/O7 8‑bit bidirectional bus for command, address, and data transfer CLE (Command Latch Enable) When high, commands are latched into the command register ALE (Address Latch Enable) When high, addresses are latched into the address register CE# (Chip Enable) Enables the device RE# (Read Enable) Enables serial data output during a read cycle WE# (Write Enable) Enables serial data input during a write cycle WP# (Write Protect) Provides hardware protection against accidental program or erase R/B# (Ready/Busy) An open‑drain, active‑low output that indicates the status of program and erase operations (low = busy) [12†L22] VCC Power supply (1.7V to 1.95V) VSS Ground This multiplexed architecture creates a low pin‑count device with a standard pinout that remains the same across densities, enabling future upgrades to higher densities with no board redesign [7†L18-L20].

A: As an SLC NAND Flash device, the MT29F4G08ABBEAH4:E is engineered for high reliability. Key reliability figures include: Reliability Parameter Specification Program/Erase Endurance 100,000 cycles (minimum) – typical for SLC NAND Data Retention 10 years (minimum) – under normal operating conditions Page Program Time (tPROG) 200 µs (typical) – self‑timed [13†L12] Block Erase Time (tBERS) 2 ms (typical) [13†L12] Page Read Time (tR) 25 µs (typical) [12†L15] Operating Temperature (Commercial Grade) 0°C to +70°C [8†L10] Important Notes on Device Management: ECC Requirement: The device does not have on‑chip ECC. External Error Correction Code (ECC) must be implemented in the host controller (typically 1‑bit ECC per 512 bytes of data) to achieve the full 100,000 program/erase cycles and 10‑year data retention specifications. The first block (block address 00h) is valid when shipped from the factory but still requires ECC management [12†L23-L25]. Initial Invalid Blocks: All NAND Flash devices, including this one, may have some initial invalid blocks when shipped from the factory. The first block (block address 00h) is guaranteed to be a valid block and does not require ECC for up to 1,000 program/erase cycles [12†L23-L25]. Bad Block Management: The system software must implement bad block management to create a table of valid blocks before performing program or erase operations. Power‑On Initialization: The RESET (FFh) command must be sent as the first command after power‑on to ensure proper device initialisation [12†L25].

A: The MT29F4G08ABBEAH4:E is suitable for a wide range of applications requiring reliable, high‑density non‑volatile code and data storage. Typical applications include: Embedded systems – Industrial PCs, single‑board computers, and module‑level designs Industrial control systems – PLCs, HMIs, data loggers, and factory automation equipment Consumer electronics – Smart TVs, set‑top boxes, digital cameras, portable media players Networking and telecommunications – Routers, switches, base stations, and broadband access equipment Medical devices – Diagnostic equipment and patient monitors Solid‑state storage – USB flash drives, memory cards, and embedded storage modules ⚠️ Important Lifecycle Information: The product lifecycle status for the MT29F4G08ABBEAH4:E is contradictory across authoritative distributor sources: Mouser explicitly lists the lifecycle for the industrial version (MT29F4G08ABBEAH4-IT:E) as "End of Life: Scheduled for obsolescence and will be discontinued by the manufacturer" [14†L8-L10]. Win‑Source (for the standard commercial version) lists the Product Status as "Obsolete" [5†L10-L11]. Xinpian‑IC lists the Part Status as "停产" (Discontinued / Obsolete) [11†L6-L7]. AVA lists the lifecycle status for the industrial version as "Obsolete" , stating "this product is no longer in active development or production" [3†L12-L14]. However, MicroMouser lists the Part Lifecycle Code as "Active" for the industrial version [15†L8], indicating ongoing active production. The product datasheet (published 2012/2014) confirms this is an older generation SLC NAND device, and similar parts have long since transitioned to newer die revisions [12†L7]. Given the conflicting lifecycle reports (Mouser "End of Life" vs. other sources "Active"), engineers are strongly advised to verify current lifecycle status, availability, and lead times directly with an authorised Micron distributor (such as Mouser, Digi‑Key, Future Electronics, or Arrow) before committing this part to a new high‑volume design. For new designs requiring a 4Gb SLC NAND Flash with an 8‑bit interface and a 63‑ball VFBGA package, the following active replacement alternatives are recommended: Alternative Part Manufacturer Package Notes MT29F4G08ABBEAH4-IT:E TR Micron VFBGA‑63 Industrial temperature (–40°C to +85°C) variant of the same device; may still be in limited production MT29F4G16ABADAH4:D Micron VFBGA‑63 4Gb x16 SLC NAND Flash with x16 I/O, active production GD9FS1G6F3ALGI GigaDevice 63‑ball VFBGA Pin‑compatible replacement (x8/x16 configurable), active production W29N04GVSIAA Winbond TSOP‑48 4Gb SLC NAND Flash, TSOP‑48 package alternative IS34ML04G081-TLI ISSI TSOP‑48 4Gb SLC NAND, industrial temperature, active production For legacy systems already using this part, remaining inventory may still be available through specialty distributors (e.g., Mouser reports 351 units in stock as of June 2025 [14†L10]). However, long‑term supply cannot be assumed. Qualification of a replacement part is strongly recommended for any new or upgraded production.