Macronix

MX25L12835FM2I-10G

A: The MX25L12835FM2I-10G delivers high performance and low power consumption, making it ideal for demanding embedded systems. Key specifications are: Specification Value Memory Density 128 Mbit (16 Mbyte) Memory Organization 16M × 8 bits / 32M × 4 bits / 64M × 2 bits Max Clock Frequency 104 MHz (supports up to 133MHz per protocol) Supply Voltage (VCC) 2.7V to 3.6V Interface Type SPI (Single, Dual I/O, Quad I/O, QPI) Max. Access Time (tAC) 8 ns Page Size 256 bytes Program/Erase Endurance 100,000 cycles minimum Data Retention 20 years minimum Operating Temperature (Industrial) –40°C to +85°C Package 8‑pin SOP (SOIC‑8 208mil) Write Protection Hardware and software write protection, absolute write protect, write enable latch Page Program Time (Tpp) 0.5 ms (500 µs) RoHS / Halogen-Free Status RoHS3 Compliant / Lead‑free

A: The MX25L12835FM2I-10G uses a standard 4‑wire Serial Peripheral Interface (SPI) bus, operating in either SPI Mode 0 (CPOL=0, CPHA=0) or Mode 3 (CPOL=1, CPHA=1), ensuring maximum compatibility with a wide range of microcontrollers and SoCs. The interface consists of the following signals: CLK (Serial Clock), CS# (Chip Select), SI / IO0 (Serial Data Input), SO / IO1 (Serial Data Output), WP# / IO2 (Write Protect), and HOLD# / IO3 pins. The device supports flexible interface modes: Single SPI (Standard): Uses separate SI (data in) and SO (data out) pins for 1‑bit transfers. Dual I/O (Dual SPI): The SI and SO pins become bidirectional I/O pins (IO0 and IO1) for 2‑bit per cycle transfers, effectively doubling the data rate. Quad I/O (Quad SPI): All four I/O pins (IO0, IO1, IO2, IO3) are used for simultaneous data transfer, achieving 4‑bit per cycle throughput — equivalent to an effective data rate of up to 416 MHz when operating at 104 MHz. QPI (Quad Peripheral Interface): The device can also operate entirely in 4‑bit mode, further reducing command overhead and improving throughput.

A: The MX25L12835FM2I-10G is engineered for long‑term reliability in demanding embedded applications. Key reliability specifications include: Reliability Parameter Specification Program/Erase Endurance 100,000 cycles minimum per sector (typical) Data Retention 20 years minimum Page Program Time (Tpp) 0.5 ms (500 µs) max for a 256‑byte page Max. Access Time (tAC) 8 ns Operating Temperature (Industrial) –40°C to +85°C Max Operating Current 25 mA Standby Current Not publicly specified, typical low power consumption for standby modes The device also includes hardware and software write protection features (absolute write protect and write enable latch), ensuring data integrity in mission‑critical systems. The uniform sector architecture (4Kbyte × 4096 sectors) allows for highly granular erase operations, minimising write amplification and extending effective device lifetime in data‑logging applications.

A: The MX25L12835FM2I-10G is well‑suited for a wide range of embedded applications requiring reliable, high‑density code and data storage with a simple, low‑pin‑count interface. Typical applications include automotive electronics, industrial control systems (PLCs, HMIs, data loggers), consumer electronics (smart TVs, set‑top boxes, digital cameras), telecommunications and networking equipment (routers, switches), medical devices, aerospace avionics, security surveillance, and energy management systems. It is also widely used for firmware and boot code storage (bootloaders, BIOS, and application code), Execute‑In‑Place (XIP) operation (allowing the host to execute code directly from the flash without copying it to RAM first), and firmware updates (supporting IAP and OTA upgrades). ⚠️ Important Lifecycle Information: The product lifecycle status for the MX25L12835FM2I-10G is contradictory across authoritative distributor and manufacturer sources. The component is not recommended for new designs, with a listed Part Status of NRND (Not For New Designs), and some sources specifically mark the part as "Not For New Designs" and "Non-recommended product". However, the part is still Active in many supply chain databases, and major distributors (DigiKey, Mouser, Arrow) continue to list the part with thousands of units in stock. Given that the part is designated as NRND (Not for New Designs) by the manufacturer, engineers are strongly advised to verify current lifecycle status, availability, and lead times directly with an authorised Macronix distributor (such as DigiKey, Mouser, Farnell, or Arrow) before committing this part to a new high‑volume design. For projects requiring long‑term supply assurance, the manufacturer recommends evaluating the MX25L12835F family or other active Macronix serial NOR Flash families (e.g., MX25L128XX series) for new designs. For legacy systems already using this part, remaining inventory may still be available through specialist distributors, but long‑term supply cannot be assured.